Tutorial: In the Beginning Part 4 Last edited 21 years ago2002-11-06 05:00:00 UTC

You are viewing an older revision of this wiki page. The current revision may be more detailed and up-to-date. Click here to see the current revision of this page.

This article was converted from a previous version of TWHL and may need to be reviewed

  1. The formatting may be incorrect due to differences in the WikiCode processing engine, it needs to be revised and reformatted
  2. Some information may be out of date
  3. After the article is re-formatted and updated, remove this notice and the Review Required category.
  4. Some older tutorials are no longer useful, or they duplicate information from other tutorials and entity guides. In this case, delete the page after merging any relevant information into other pages. Contact an admin to delete a page.

Download attachment

In this tutorial we will look at the effects of lighting. Good lighting is great for atmosphere. It's also good to have a few dark places but not too many. [Continue with the map from part 3].

UPDATE: Before we go any further, when you compiled your map, did the light look as though there was a real light? By that I mean, did the map look as though there was a light where you placed it or did it look like the whole map was floodlit?. If it looked floodlit or really bright, then you might want to compile it again and look at the Error Log. It is normally saved in the same area as your .rmf file. Look for a line that indicates an Error. If there is a LEAK in your map, then the map will be floodlit or "Fullbright". If you do not fix the LEAK, then the rest of this tutorial is pointless, because you will not see the lighting as it is meant to be. The reason I waited this long to mention this, is that without a texture applied to the walls, it is hard to tell if the map is Fullbright or not. Another way to check for a LEAK is to bring up the console with the ~ key and type in pointfile. If there is a LEAK, the pointfile will be generated and it will tell you the number of points read. If it is 0 then congratulations: your map doesn't LEAK...yet.

The Properties dialog (found by right-clicking the light entity) allows you to customize the brightness, colour, appearance (flickering, fading, etc), target, and name of the light.
Setting the brightnessSetting the brightness
Also, in the Flags section, you have the option of indicating that the light should be Initially Dark. In this case you'd also have to supply a name for the light so it could be "triggered" to turn on.
Warm but also depressingWarm but also depressing
Cold and starkCold and stark
Nuclear holocaust, anyone?Nuclear holocaust, anyone?
The effect created by just changing the colour is dramatic. The first figure uses the default settings. For the second room I have selected the light's properties and highlighted Brightness. This will bring up an additional setting, Pick Color.
You have a huge range of different colour options avaliable to youYou have a huge range of different colour options avaliable to you
Clicking on this option takes you to a colour palette where you can choose what suits you. The colour palette has an Add to Custom Colors button - if you find a colour that suits the theme of your room, just click that bar to save the colour. It will appear under Custom Colors: this will remain set even when you close the map or compile it. Great for large levels that need consistency. You can see from the figure that I have saved the three Colours used above. The default Brightness setting is the yellow hue shown.

Placement of the lights has a varied effect. The lights in the figures above are 8 units below the ceiling. Adding a ceiling light fixture will enhance the effect.

Working with Light Textures

There are a lot of textures that can be used and the easiest way to find them is to open your texture browser and type + in the filter [or have a look in the file lights.rad in your WorldCraft folder]. Create a brush 64x80x4 units to apply your light texture to. In the example map I have used +0~fifts_lght01 (because the texture size is the same as the brush) and applied another texture to the border of the light. Place this brush in the centre of the room above the existing light. To add a little realism to the light you might want to change the light entity property Appearance to Flicker A. The Fluorescent Flicker setting actually turns the light off and on, transitioning the room between light and dark.

Most light textures can be used in conjunction with func_ entities, by setting the Minimum Light Level in the entity properties to > 1. This gives the appearance of the texture being lit, but adds no light to the actual room. If you add a light texture to the borders of your light brush, they will also light up and sometimes this lessens the effect and reduces the shadow, giving the light an unnatural look.
Minimum light level: 1Minimum light level: 1
Minimum light level: 0Minimum light level: 0
Create a small brush using the exit1 texture on the front face and position it above the corridor (makes sense). Select the brush and change it to a func_wall entity with a Minimum Light Level of 1 (you can make this value 500, but it doesn't make any difference. The range is 0 to 1, so 0.5 is half-lit). The figures above show the enhancement gained by applying an entity to the brush. If you don't have any light in the room, and there is a really inviting "EXIT" sign at the other end, it doesn't take a genius to work out where your player is going to go. Great place for a trap or monster trigger.

NOTE: If you give the light a name to use with a trigger or switch, remember that the game engine can only cope with about 4 named lights or animated lights in the same visual area. More than that might produce weird effects and an error in some compiling programs. I am not sure how many unnamed lights the engine can cope with, but less is better. Did you see I said, "might produce"... well thats right, you might be lucky, LightForce reported that he managed to get lot's of named lights working, so you will have to experiment.[BR] The same applies with light_spot entities. And speaking of light_spot entities, Atom has a tutorial called Environment that deals with some of the effects you get using this entity. In this tutorial, the spare room has a light_spot entity with all its properties set to default with the exception of the Outer Fading Angle which has been set to 180.

UPDATE: There have been a lot of questions about lighting. As I said in the first paragraph, if your map does not compile properly or VIS and RAD do not finish, then your map will be lit "Fullbright" and any changes you have made to the lights properties will not show in the final map. Be sure to check for LEAK's as this is the most common cause.

Experiment and try new things. The secret to a good level is in the texturing and the lighting. Got any good suggestions? Post them in the forum.

? Part 5: Furniture Prefabs

Comments

You must log in to post a comment. You can login or register a new account.