Vlatitude Archive: Rocks and Cliffs Last edited 5 years ago2019-04-25 09:18:55 UTC

You are viewing an older revision of this wiki page. The current revision may be more detailed and up-to-date. Click here to see the current revision of this page.
Download example

Between a rock and a hard place

WARNING: This guide is aimed at those who are familiar with WC and general mapping practices.

This guide is designed to help those who are struggling to create good outside environments with realistic scenery such as rocks, cliffs and other natural features. While HL is not the perfect engine for large areas, it can do this very well using complex shapes. However, this technique requires the mapper to carefully control these odd shapes, thus avoiding invalid shape errors and clipping problems. This guide looks at how to create good cliffs and rocks in an area that won't receive much action, meaning that r-speeds that don't result from our cliffs have to be lower. Our target for this area would be an average r-speeds of about 700-800. The reason that this guide targets this range is because it allows you to fully make use of the methods explained, meaning that you are able to cut back on things if you want to make a lower r-speed area.
User posted image
To make a good cliff, you will need to make it out of many brushes stacked one on top of the other. This formation allows for maximum control of the cliff shape while avoiding errors. It also allows using more than one texture if necessary. The cliff pictured is going to be used as a visual reference; the sample map available is from a different map, but shows off this method at its best.

One thing you should remember is to use the cubic brush when you first start, this means that you will always have plenty of excess edges to trim away. Like doing work with clay, it's best to start with too much than to find that you need to add more later. Now once you have everything laid out you should start slicing edges of with the clipping tool. This works much like a knife and helps to avoid errors caused if you use the vertex tool.
User posted image
User posted image
Depending on what you want the cliff to look like, you may want a uniform shape along the vertical axis of each stack. Select all the cubes in a single stack and cave them all in one go. When ever you start carving complex shapes like this, the first slices should be done from the top view. Most real cliff faces however will not be the same from the bottom all the way to the top. By stacking the brushes you can make cuts that allow the cliff to have indents and grooves. If you look at many cliffs you will see that the bottom is thinner than the middle due to erosion from water and other things. Keep things like this in mind while you are carving.

You can however still develop errors from the carving process. If you find that you get an invalid brush error turning up, then it's because you have created a side of the brush that is very, very thin. The problem finder will lead you to offending brush and then you will have to get very close to it in order to find the edge. Locate the vertices in the 3D view and select them. Then move it to the nearby vertices on the same edge to weld them together into one vertice. You will have to do that twice for each face.

You can only carve from 2 sides without rotating the brush. This can lead to problems if you have the cliffs on the outer edge of your map with a sky brush behind. When you cut off a large section of the cliff, the sky brush may become visible in the gap. To solve this problem, you can pull a little trick. Before you cut the brush, first select it and chose copy from the menu. Make your cut and then right click to bring up the menu again. Select paste special. Paste the copy at 0,0,0 from the origin of the original. Now slice this new brush the opposite way that you cut the original. In other words you are trying to make the original shape of the brush from 2 brushes. You can then cut this new brush from above to hide the sky visible behind it.
User posted image
Now you will have the whole cliff completely caved out, you will notice that some faces have hugely distorted textures. This error occurs due to a bug in WC 3.3. Bring out the texture tool and set it to 'LIFT and SELECT'. Click on these distorted texture faces and you will see that they have no 'alignment' flag. I'd suggest ticking the 'TO WORLD' flag rather than the 'TO FACE' flag because the latter can cause slightly misaligned textures. Check all the faces to avoid errors in the compile that sometimes say 'texture axis perpendicular to face'.

Now whenever you make large areas it's very important to scale 'up' the textures whenever possible. Changing a flat surface's texture from the regular x1 scale to x2 will nearly half the number of polygons it will be composed from in the actual game. With large cliffs, you can sometimes get away with having a x3 scale texture.
User posted image
The picture above is of the completed cliff. Another element that is available with the stacking method is the use of special textures for the uppermost brush and the bottom brush. For example, there are some HL rock textures that have more then one type in a set. There's the regular rock, and then there is rock with sand on the lower edge. Since you have an individual brush on the bottom of the stack, you can use this sandy rock texture to achieve a realistic visual effect. This would not be possible with a single tall brush using just one texture.

Just a note: the pictured cliff had a maximum r_speed of only 350.

Lastly, you should remember that you want uneven ground if you are on surfaces made of sand, mud, snow, or grass. While materials like grass and mud will just have small hills, stuff like snow and sand will tend to also make mounds against objects as they are blown by the wind. On the pictured map there are some small mounds of snow against the walls. To stop these from upping the r-speeds due to their strange shape touching other brushes and breaking them up, you should make them func_wall entities.

That's everything there is to say on the matter of vertical stacking. But remember that you can get a similar effect with other surfaces if you make them up from more than one brush. Programs like GENSURF use the same method and any mapper should consider this program as yet another tool for making realistic organic scenery.
This article was originally published on 69th Vlatitude.
TWHL only archives articles from defunct websites. For more information on TWHL's archiving efforts, please visit the TWHL Archiving Project page.

Comments

You must log in to post a comment. You can login or register a new account.