Wiki: env_fade

env_fade - Point Entity

The env_fade entity, when triggered, gradually covers the screen with a single-colour overlay. Typically used for fading a scene in or out.

Attributes

Name (targetname) - Name is a general attribute used to identify entities.
Duration (seconds) (duration) - Sets how long the overlay should take to fade into its full effect.
Hold Fade (seconds) (holdtime) - Sets how long the overlay should stay on the screen at its full effect before turning itself off.
Fade Alpha (renderamt) - The maximum alpha value (opacity) of the overlay. Scales from 0 (transparent) to 255 (opaque).
Fade Color (R G B) (rendercolor) - Sets the color of the overlay.

Flags

Fade From (1) - If enabled, the overlay starts at the maximum alpha value and goes in reverse. (Essentially changes it from a fade out to a fade in.)
Modulate (2) - If enabled, the env_fade will use an alternative rendering mode for the overlay. Multiplies the color of the overlay against the game scene. (Essentially recolours the scene rather than covering it with a solid colour.)
Activator Only (4) - If enabled, the fade will only affect the player who activated it.

Notes

If Duration is set to 0, the env_fade will not do anything. If you require a sudden overlay, set Duration to a very small amount such as 0.1.

From the VERC Archive

Usage

Setup is simple:

Place the entity in your level. Its location is unimportant.
Give it a Name (targetname). The entity must be triggered to take effect.
Give it a Duration (duration) and Hold Fade (holdtime) time. Duration controls how long it takes to fade from normal to the fade color (or the reverse, if the Fade From flag is checked) and Hold Fade controls how long the screen stays at the fade color. Add these two values together for the total time this entity will be in effect.
Set the Fade Alpha (renderamt). This controls the level of fade. A Fade Alpha of 128 would fade the screen half-way between normal and the fade color (below). For a solid fade, a value of 255 can be used.
Set the Fade Color (rendercolor). This is the RGB color the screen will fade to. It defaults to black (0 0 0).

Modulate

The modulate flag on the fade does a different kind of blending to achieve the fade. The normal fade does a straight weighted blend between the screen and the fade's color (i.e. the fade color becomes a more/less opaque overlay over the scene). Modulate actually attenuates the screen colors in r/g/b with the fade color. So you could, for example, remove all of the red & blue from a scene with modulate and be left with a green "night-vision" display - well sort of night vision anyway. The fade color for that would be pure green with modulate. If you uncheck the modulate flag, it will turn the screen completely solid green.

Example maps

Loading embedded content: Vault Item #1782

Loading embedded content: Vault Item #5500

Loading embedded content: Vault Item #6681

Skals

Commented 14 years ago2010-07-11 21:50:13 UTC Comment #101069

MODULATE EXAMPLE HERE: http://twhl.co.za/vault.php?map=5500

-- flag info: Rather than fully colouring up the entire screen, it acts as a layer of the chosen colour and FX, For example, if you make the FX 255, the colour red and tick the modulate flag, Your entire screen will be covered in red but you will still freely see, it will look as if your ordinary yellow light bulbs suddenly turn red.

KaLo

Commented 13 years ago2011-04-30 16:25:00 UTC Comment #101070

what flags is effects for all players?

User#6970

Commented 7 years ago2017-11-07 02:53:10 UTC Comment #101071

4: "Activator only": If set, only the player who activated this entity will be affected by it.

Source: http://zyl.pestermom.com/external/entguide/entities/env_fade.html.

env_fade Last edited 11 months ago2024-01-19 01:30:59 UTC