Wiki: multi_manager (Half-Life)

This article was converted from a previous version of TWHL and may need to be reviewed

The formatting may be incorrect due to differences in the WikiCode processing engine, it needs to be revised and reformatted
Some information may be out of date
After the article is re-formatted and updated, remove this notice and the Review Required category.
Some older articles are no longer useful, or they duplicate information from other pages. In this case, delete the page after merging any relevant information into other pages. Contact an admin to delete a page.

Point Entity

This entity can activate several different events (including itself) at specific times.

Attributes

Name (targetname) - Property used to identify entities.

Flags

Multithreaded (1) - See notes below for an explanation.

Inputs

Outputs

Notes

Maximum of 16 individual targets.

To add targets, disable SmartEdit, then click Add and enter the Name as the new Key and a delay in seconds as the Value, then click OK.

<B>Multithreading:</B> Normally, If the multi_manager is called again before it has finished its work-order, it will ignore the new call and will just carry on with its work. However, with the Multithreaded flag enabled, when the manager is called again, it will continue working while another 'copy' of the multi_manager will start up. This solves various problems, mainly related to multiplayer games (where you might want a multi_manager to start up for each player that joins - if one player joins while the multimanager is still going for another player, a new thread needs to be created).

Captain Terror

Commented 16 years ago2008-05-28 02:43:39 UTC Comment #101112

Multi_managers and looping note:

If your using an MM as a continuous loop (by having the MM call itself at the end of it's routine), it will only loop if you have the "multithreaded" flag checked!

Captain Terror

Commented 15 years ago2009-02-24 09:41:18 UTC Comment #101113

"Maximum of 16 individual targets. "

More like 8, to keep it safe. Check out this thread for more info! = )

Stojke

Commented 12 years ago2012-03-14 20:31:33 UTC Comment #101114

Pay attention to the "Game crash" warning as it is the usual case of map crashes when using this technique.

Also don't forget to make the start time 0.1 and not 0, as 0 can cause the map to crash and/or other game bugs.
That said, when deactivating something, lets say:

00laser1 0.1
00laser1#1 2.1
00laser1#2 ??

Do NOT start it after it is deactivated (00laser1#2 2.1), give it 0.1 seconds freeze time (or more if you need it):

00laser1 0.1
00laser1#1 2.1
00laser1#2 2.2

And remember not to use long entity names, for example (i use):

0lsrmm (Laser control multi manager)
0expmm (Explosion control multi manager)

User#6970

Commented 7 years ago2017-11-22 23:31:59 UTC Comment #101115

Proper looping:

Proper looping is done with an env_beam repeatedly shooting through a func_button with health = 1. info_targets must sandwich the button. The button activates the multi.

The env_beam must have damage set to >=1. Change Strike again time to set the loop frequency.

Note: You'll lose the activator (current player) reference.

Linda420303

Commented 9 months ago2024-02-01 20:16:02 UTC Comment #105948

multi_manager supports triggerstates, by default its use-type is "Toggle".
Add a "#x" at the end of the value, where "x" is the triggerstate value:

"0.001#0" means to trigger via use-type Off after 0.001s
"0.001#1" means to trigger via use-type On after 0.001s
"0.001#2" means to trigger via "killtarget" triggerstate after 0.001s

multi_manager is basically a trigger_relay now with this knowledge!

Admer456

Commented 9 months ago2024-02-02 01:53:19 UTC Comment #105949

I think that's Sven Co-op-specific, isn't it?
opens up the code
Yeah, there's nothing in HL SDK that points to the parsing of #N there. It is always USE_TOGGLE. Either way though, good to know!

multi_manager (Half-Life) Last edited 16 years ago2008-06-11 08:13:41 UTC